Carte Wifi TP-Link TL-WN422G driver ?

Support Debian
#1

Bonjour tout le monde , c’est la 1er fois que j utilise debian
j ai installé wifi-radar mais je ne capte pas mon réseau
Carte usb Wifi TP-Link TL-WN422G
Aidez-moi svp :confused:

le noyau employé :

Linux ws031347 2.6.26-2-amd64 #1 SMP Wed Aug 19 22:33:18 UTC 2009 x86_64 GNU/Linux

matériel

[code]00:00.0 RAM memory: nVidia Corporation MCP67 Memory Controller (rev a2)

00:01.0 ISA bridge: nVidia Corporation MCP67 ISA Bridge (rev a2)

00:01.1 SMBus: nVidia Corporation MCP67 SMBus (rev a2)

00:01.3 Co-processor: nVidia Corporation MCP67 Co-processor (rev a2)

00:02.0 USB Controller: nVidia Corporation MCP67 OHCI USB 1.1 Controller (rev a2)

00:02.1 USB Controller: nVidia Corporation MCP67 EHCI USB 2.0 Controller (rev a2)

00:04.0 USB Controller: nVidia Corporation MCP67 OHCI USB 1.1 Controller (rev a2)

00:04.1 USB Controller: nVidia Corporation MCP67 EHCI USB 2.0 Controller (rev a2)

00:06.0 IDE interface: nVidia Corporation MCP67 IDE Controller (rev a1)

00:07.0 Audio device: nVidia Corporation MCP67 High Definition Audio (rev a1)

00:08.0 PCI bridge: nVidia Corporation MCP67 PCI Bridge (rev a2)

00:0a.0 Ethernet controller: nVidia Corporation MCP67 Ethernet (rev a2)

00:0b.0 PCI bridge: nVidia Corporation MCP67 PCI Express Bridge (rev a2)

00:0c.0 PCI bridge: nVidia Corporation MCP67 PCI Express Bridge (rev a2)

00:0d.0 PCI bridge: nVidia Corporation MCP67 PCI Express Bridge (rev a2)

00:0e.0 PCI bridge: nVidia Corporation MCP67 PCI Express Bridge (rev a2)

00:0f.0 PCI bridge: nVidia Corporation MCP67 PCI Express Bridge (rev a2)

00:10.0 PCI bridge: nVidia Corporation MCP67 PCI Express Bridge (rev a2)

00:11.0 PCI bridge: nVidia Corporation MCP67 PCI Express Bridge (rev a2)

00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration

00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map

00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller

00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control

02:00.0 VGA compatible controller: nVidia Corporation NV41.2 [GeForce 6800 LE] (rev a2)

[/code]

$ lsusb

[code]Bus 004 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub

Bus 003 Device 004: ID 1005:b113 Apacer Technology, Inc. Handy Steno 2.0/HT203

Bus 003 Device 002: ID 0ace:1215 ZyDAS WLA-54L WiFi

Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub

Bus 002 Device 002: ID 1241:1111 Belkin Mouse

Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub

Bus 001 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub

[/code]

#2

Avant tout, l’adaptateur est-il bien détecté, le module zd1211rw est-il bien chargé (lsmod) pour le piloter, une interface réseau est-elle bien créée (ifconfig -a) ? Y a-t-il des messages du noyau concernant ce module ou cette interface (dmesg) ?

S’il y a un message du type “RF MAXIM_NEW_RF 0x8 is not supported”, j’ai trouvé ce patch dans le changelog du noyau 2.6.27.18 :

[quote]zd1211rw: treat MAXIM_NEW_RF(0x08) as UW2453_RF(0x09) for TP-Link WN322/422G

commit efb43f4b2ccf8066abc3920a0e6858e4350a65c7 upstream.

Three people […] reported success in getting TP-Link WN322G/WN422G working by treating MAXIM_NEW_RF(0x08) as UW2453_RF(0x09) for rf chip hardware initialization.[/quote]
Malheureusement, ce patch n’a été intégré que dans les versions 2.6.27.18, 2.6.28.6, 2.6.29 et au-delà du noyau standard. J’ai vérifié rapidement dans la liste des patches Debian pour le noyau 2.6.26 de lenny (paquet linux-patch-debian-2.6.26), il n’a pas l’air d’y être. Néanmoins si tu sais recompiler le module ou le noyau, le patch est trivial (une ligne à ajouter dans un fichier source) et devrait s’appliquer aux sources du noyau 2.6.26.

#3

PascalHambourg merci pour ta repense
Malheureusement je ne sais pas recompiler ni module ni le noyau :frowning:
quand j ai utiliser

ifconfig -a

[code]eth0 Link encap:Ethernet HWaddr 00:19:66:89:46:75

      UP BROADCAST MULTICAST  MTU:1500  Metric:1

      RX packets:0 errors:0 dropped:0 overruns:0 frame:0

      TX packets:0 errors:0 dropped:0 overruns:0 carrier:0

      collisions:0 lg file transmission:1000 

      RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

      Interruption:248 Adresse de base:0x8000

lo Link encap:Boucle locale

      inet adr:127.0.0.1  Masque:255.0.0.0

      adr inet6: ::1/128 Scope:Hôte

      UP LOOPBACK RUNNING  MTU:16436  Metric:1

      RX packets:45 errors:0 dropped:0 overruns:0 frame:0

      TX packets:45 errors:0 dropped:0 overruns:0 carrier:0

      collisions:0 lg file transmission:0 

      RX bytes:19789 (19.3 KiB)  TX bytes:19789 (19.3 KiB)

wlan0 Link encap:Ethernet HWaddr 00:23:cd:b7:70:f9

      BROADCAST MULTICAST  MTU:1500  Metric:1

      RX packets:0 errors:0 dropped:0 overruns:0 frame:0

      TX packets:0 errors:0 dropped:0 overruns:0 carrier:0

      collisions:0 lg file transmission:1000 

      RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

wmaster0 Link encap:UNSPEC HWaddr 00-23-CD-B7-70-F9-00-00-00-00-00-00-00-00-00-00

      BROADCAST MULTICAST  MTU:1500  Metric:1

      RX packets:0 errors:0 dropped:0 overruns:0 frame:0

      TX packets:0 errors:0 dropped:0 overruns:0 carrier:0

      collisions:0 lg file transmission:1000 

      RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

[/code]

lsmod:

[code]Module Size Used by

nls_utf8 6272 1

nls_cp437 11136 1

vfat 14976 1

fat 51128 1 vfat

nls_base 12932 4 nls_utf8,nls_cp437,vfat,fat

nvidia 8105072 24

i2c_core 27936 1 nvidia

ppdev 11656 0

lp 14724 0

ipv6 288456 25

powernow_k8 17156 0

cpufreq_userspace 8452 0

cpufreq_powersave 6400 0

cpufreq_ondemand 11792 1

cpufreq_stats 9120 0

freq_table 9344 3 powernow_k8,cpufreq_ondemand,cpufreq_stats

cpufreq_conservative 11784 0

loop 19468 0

sd_mod 29376 2

irtty_sir 9728 0

sir_dev 16904 1 irtty_sir

parport_pc 31016 1

parport 41776 3 ppdev,lp,parport_pc

irda 117732 1 sir_dev

arc4 6272 2

ecb 7296 2

crypto_blkcipher 21636 1 ecb

k8temp 9216 0

crc_ccitt 6528 1 irda

pcspkr 7040 0

snd_hda_intel 436696 1

snd_pcm 81800 1 snd_hda_intel

snd_seq 54304 0

snd_timer 25744 2 snd_pcm,snd_seq

snd_seq_device 11668 1 snd_seq

snd 63688 7 snd_hda_intel,snd_pcm,snd_seq,snd_timer,snd_seq_device

soundcore 12064 1 snd

snd_page_alloc 13072 2 snd_hda_intel,snd_pcm

zd1211rw 49928 0

firmware_class 12544 1 zd1211rw

mac80211 162992 1 zd1211rw

cfg80211 30224 1 mac80211

wmi 11712 0

button 11680 0

evdev 14208 3

ext3 125072 1

jbd 51240 1 ext3

mbcache 12804 1 ext3

usbhid 45792 0

hid 41792 1 usbhid

ff_memless 9224 1 usbhid

ide_disk 16512 3

ide_cd_mod 36360 0

cdrom 37928 1 ide_cd_mod

usb_storage 95936 1

amd74xx 13448 0 [permanent]

ide_pci_generic 9220 0 [permanent]

ide_core 128284 4 ide_disk,ide_cd_mod,amd74xx,ide_pci_generic

forcedeth 54032 0

ata_generic 10116 0

libata 165600 1 ata_generic

scsi_mod 161016 3 sd_mod,usb_storage,libata

dock 14112 1 libata

ehci_hcd 36108 0

ohci_hcd 25092 0

thermal 22688 0

processor 42304 2 powernow_k8,thermal

fan 9352 0

thermal_sys 17728 3 thermal,processor,fan
[/code]

dmesg:

[code][ 0.220171] pnp 00:04: io min 0x2e8 max 0x2e8 align 1 size 8 flags 0x1

[ 0.220175] pnp 00:04: irq bitmask 00000000,00000000,00000000,00000000,00000000,00000000,00000000,00001cf8 flags 0x1

[ 0.220178] pnp 00:04: dma bitmask 0xf flags 0x0

[ 0.220180] pnp 00:04: end dependent options

[ 0.220222] pnp 00:04: Plug and Play ACPI device, IDs PNP0510 (active)

[ 0.220747] pnp 00:05: parse allocated resources

[ 0.221327] pnp 00:05: add io 0x378-0x37f flags 0x1

[ 0.221329] pnp 00:05: add io 0x778-0x77f flags 0x1

[ 0.221337] pnp 00:05: add irq 7 flags 0x1

[ 0.221339] pnp 00:05: add dma 3 flags 0x0

[ 0.221341] pnp 00:05: parse resource options

[ 0.221343] pnp 00:05: new independent option

[ 0.221569] pnp 00:05: new dependent option (priority 0x0)

[ 0.221571] pnp 00:05: io min 0x378 max 0x378 align 1 size 8 flags 0x1

[ 0.221574] pnp 00:05: io min 0x778 max 0x778 align 1 size 8 flags 0x1

[ 0.221579] pnp 00:05: irq bitmask 00000000,00000000,00000000,00000000,00000000,00000000,00000000,00000080 flags 0x1

[ 0.221582] pnp 00:05: dma bitmask 0x8 flags 0x0

[ 0.221584] pnp 00:05: new dependent option (priority 0x1)

[ 0.221587] pnp 00:05: io min 0x378 max 0x378 align 1 size 8 flags 0x1

[ 0.221590] pnp 00:05: io min 0x778 max 0x778 align 1 size 8 flags 0x1

[ 0.221594] pnp 00:05: irq bitmask 00000000,00000000,00000000,00000000,00000000,00000000,00000000,00001cf8 flags 0x1

[ 0.221598] pnp 00:05: dma bitmask 0xf flags 0x0

[ 0.221600] pnp 00:05: new dependent option (priority 0x1)

[ 0.221602] pnp 00:05: io min 0x278 max 0x278 align 1 size 8 flags 0x1

[ 0.221605] pnp 00:05: io min 0x678 max 0x678 align 1 size 8 flags 0x1

[ 0.221610] pnp 00:05: irq bitmask 00000000,00000000,00000000,00000000,00000000,00000000,00000000,00001cf8 flags 0x1

[ 0.221613] pnp 00:05: dma bitmask 0xf flags 0x0

[ 0.221615] pnp 00:05: new dependent option (priority 0x1)

[ 0.221617] pnp 00:05: io min 0x3bc max 0x3bc align 1 size 4 flags 0x1

[ 0.221620] pnp 00:05: io min 0x7bc max 0x7bc align 1 size 4 flags 0x1

[ 0.221625] pnp 00:05: irq bitmask 00000000,00000000,00000000,00000000,00000000,00000000,00000000,00001cf8 flags 0x1

[ 0.221628] pnp 00:05: dma bitmask 0xf flags 0x0

[ 0.221630] pnp 00:05: end dependent options

[ 0.221670] pnp 00:05: Plug and Play ACPI device, IDs PNP0401 (active)

[ 0.221687] pnp 00:06: parse allocated resources

[ 0.222344] pnp 00:06: add io 0x10-0x1f flags 0x1

[ 0.222346] pnp 00:06: add io 0x22-0x3f flags 0x1

[ 0.222348] pnp 00:06: add io 0x44-0x4d flags 0x1

[ 0.222350] pnp 00:06: add io 0x50-0x5f flags 0x1

[ 0.222353] pnp 00:06: add io 0x62-0x63 flags 0x1

[ 0.222355] pnp 00:06: add io 0x65-0x6f flags 0x1

[ 0.222357] pnp 00:06: add io 0x72-0x7f flags 0x1

[ 0.222359] pnp 00:06: add io 0x80-0x80 flags 0x1

[ 0.222361] pnp 00:06: add io 0x84-0x86 flags 0x1

[ 0.222363] pnp 00:06: add io 0x88-0x88 flags 0x1

[ 0.222365] pnp 00:06: add io 0x8c-0x8e flags 0x1

[ 0.222368] pnp 00:06: add io 0x90-0x9f flags 0x1

[ 0.222370] pnp 00:06: add io 0xa2-0xbf flags 0x1

[ 0.222372] pnp 00:06: add io 0xe0-0xef flags 0x1

[ 0.222374] pnp 00:06: add io 0x4d0-0x4d1 flags 0x1

[ 0.222376] pnp 00:06: add io 0x800-0x80f flags 0x1

[ 0.222379] pnp 00:06: add io 0x1000-0x107f flags 0x1

[ 0.222381] pnp 00:06: add io 0x1080-0x10ff flags 0x1

[ 0.222383] pnp 00:06: add io 0x1400-0x147f flags 0x1

[ 0.222386] pnp 00:06: add io 0x1480-0x14ff flags 0x1

[ 0.222388] pnp 00:06: add io 0x1800-0x187f flags 0x1

[ 0.222390] pnp 00:06: add io 0x1880-0x18ff flags 0x1

[ 0.222393] pnp 00:06: add io 0x1c00-0x1c7f flags 0x1

[ 0.222395] pnp 00:06: add io 0x1c80-0x1cff flags 0x1

[ 0.222397] pnp 00:06: add mem 0x0-0xffffffffffffffff flags 0x10000000

[ 0.222400] pnp 00:06: add mem 0xfefe0000-0xfefe01ff flags 0x0

[ 0.222402] pnp 00:06: add mem 0xfefe1000-0xfefe1fff flags 0x0

[ 0.222405] pnp 00:06: add mem 0xfee01000-0xfeefffff flags 0x0

[ 0.222408] pnp 00:06: PNP0c02: calling quirk_system_pci_resources+0x0/0x15c

[ 0.222491] pnp 00:06: Plug and Play ACPI device, IDs PNP0c02 (active)

[ 0.222594] pnp 00:07: parse allocated resources

[ 0.222638] pnp 00:07: add io 0x70-0x71 flags 0x1

[ 0.222646] pnp 00:07: add irq 8 flags 0x1

[ 0.222687] pnp 00:07: Plug and Play ACPI device, IDs PNP0b00 (active)

[ 0.222705] pnp 00:08: parse allocated resources

[ 0.222797] pnp 00:08: add mem 0xfec00000-0xfec00fff flags 0x0

[ 0.222799] pnp 00:08: add mem 0xfee00000-0xfee00fff flags 0x0

[ 0.222802] pnp 00:08: PNP0c02: calling quirk_system_pci_resources+0x0/0x15c

[ 0.222866] pnp 00:08: Plug and Play ACPI device, IDs PNP0c02 (active)

[ 0.222928] pnp 00:09: parse allocated resources

[ 0.222934] pnp 00:09: add io 0x60-0x60 flags 0x1

[ 0.222936] pnp 00:09: add io 0x64-0x64 flags 0x1

[ 0.222944] pnp 00:09: add irq 1 flags 0x1

[ 0.222986] pnp 00:09: Plug and Play ACPI device, IDs PNP0303 PNP030b (active)

[ 0.223297] pnp 00:0a: parse allocated resources

[ 0.223604] pnp 00:0a: add io 0x3f8-0x3ff flags 0x1

[ 0.223612] pnp 00:0a: add irq 4 flags 0x1

[ 0.223614] pnp 00:0a: parse resource options

[ 0.223616] pnp 00:0a: new independent option

[ 0.223653] pnp 00:0a: new dependent option (priority 0x0)

[ 0.223655] pnp 00:0a: io min 0x3f8 max 0x3f8 align 1 size 8 flags 0x1

[ 0.223660] pnp 00:0a: irq bitmask 00000000,00000000,00000000,00000000,00000000,00000000,00000000,00000010 flags 0x1

[ 0.223663] pnp 00:0a: new dependent option (priority 0x1)

[ 0.223666] pnp 00:0a: io min 0x3f8 max 0x3f8 align 1 size 8 flags 0x1

[ 0.223671] pnp 00:0a: irq bitmask 00000000,00000000,00000000,00000000,00000000,00000000,00000000,00001cf8 flags 0x1

[ 0.223674] pnp 00:0a: new dependent option (priority 0x1)

[ 0.223677] pnp 00:0a: io min 0x2f8 max 0x2f8 align 1 size 8 flags 0x1

[ 0.223681] pnp 00:0a: irq bitmask 00000000,00000000,00000000,00000000,00000000,00000000,00000000,00001cf8 flags 0x1

[ 0.223684] pnp 00:0a: new dependent option (priority 0x1)

[ 0.223687] pnp 00:0a: io min 0x3e8 max 0x3e8 align 1 size 8 flags 0x1

[ 0.223691] pnp 00:0a: irq bitmask 00000000,00000000,00000000,00000000,00000000,00000000,00000000,00001cf8 flags 0x1

[ 0.223694] pnp 00:0a: new dependent option (priority 0x1)

[ 0.223697] pnp 00:0a: io min 0x2e8 max 0x2e8 align 1 size 8 flags 0x1

[ 0.223701] pnp 00:0a: irq bitmask 00000000,00000000,00000000,00000000,00000000,00000000,00000000,00001cf8 flags 0x1

[ 0.223704] pnp 00:0a: end dependent options

[ 0.223748] pnp 00:0a: Plug and Play ACPI device, IDs PNP0501 (active)

[ 0.223766] pnp 00:0b: parse allocated resources

[ 0.223886] pnp 00:0b: add io 0x0-0xffffffffffffffff flags 0x10000001

[ 0.223889] pnp 00:0b: add io 0x0-0xffffffffffffffff flags 0x10000001

[ 0.223891] pnp 00:0b: add io 0x290-0x29f flags 0x1

[ 0.223894] pnp 00:0b: PNP0c02: calling quirk_system_pci_resources+0x0/0x15c

[ 0.223959] pnp 00:0b: Plug and Play ACPI device, IDs PNP0c02 (active)

[ 0.224034] pnp 00:0c: parse allocated resources

[ 0.224100] pnp 00:0c: add mem 0xe0000000-0xefffffff flags 0x0

[ 0.224103] pnp 00:0c: PNP0c02: calling quirk_system_pci_resources+0x0/0x15c

[ 0.224167] pnp 00:0c: Plug and Play ACPI device, IDs PNP0c02 (active)

[ 0.224234] pnp 00:0d: parse allocated resources

[ 0.224449] pnp 00:0d: add mem 0x0-0x9ffff flags 0x1

[ 0.224451] pnp 00:0d: add mem 0xc0000-0xcffff flags 0x0

[ 0.224453] pnp 00:0d: add mem 0xe0000-0xfffff flags 0x0

[ 0.224456] pnp 00:0d: add mem 0x100000-0x7fffffff flags 0x1

[ 0.224458] pnp 00:0d: add mem 0xfec00000-0xffffffff flags 0x0

[ 0.224461] pnp 00:0d: PNP0c01: calling quirk_system_pci_resources+0x0/0x15c

[ 0.224529] pnp 00:0d: Plug and Play ACPI device, IDs PNP0c01 (active)

[ 0.225780] pnp: PnP ACPI: found 14 devices

[ 0.225782] ACPI: ACPI bus type pnp unregistered

[ 0.225996] usbcore: registered new interface driver usbfs

[ 0.226056] usbcore: registered new interface driver hub

[ 0.226099] usbcore: registered new device driver usb

[ 0.226263] PCI: Using ACPI for IRQ routing

[ 0.236184] ACPI: RTC can wake from S4

[ 0.248022] pnp: the driver ‘system’ has been registered

[ 0.248037] system 00:06: ioport range 0x4d0-0x4d1 has been reserved

[ 0.248040] system 00:06: ioport range 0x800-0x80f has been reserved

[ 0.248043] system 00:06: ioport range 0x1000-0x107f has been reserved

[ 0.248045] system 00:06: ioport range 0x1080-0x10ff has been reserved

[ 0.248048] system 00:06: ioport range 0x1400-0x147f has been reserved

[ 0.248051] system 00:06: ioport range 0x1480-0x14ff has been reserved

[ 0.248054] system 00:06: ioport range 0x1800-0x187f has been reserved

[ 0.248057] system 00:06: ioport range 0x1880-0x18ff has been reserved

[ 0.248060] system 00:06: ioport range 0x1c00-0x1c7f has been reserved

[ 0.248063] system 00:06: ioport range 0x1c80-0x1cff has been reserved

[ 0.248066] system 00:06: iomem range 0xfefe0000-0xfefe01ff has been reserved

[ 0.248069] system 00:06: iomem range 0xfefe1000-0xfefe1fff has been reserved

[ 0.248072] system 00:06: iomem range 0xfee01000-0xfeefffff could not be reserved

[ 0.248075] system 00:06: driver attached

[ 0.248084] system 00:08: iomem range 0xfec00000-0xfec00fff could not be reserved

[ 0.248087] system 00:08: iomem range 0xfee00000-0xfee00fff could not be reserved

[ 0.248090] system 00:08: driver attached

[ 0.248096] system 00:0b: ioport range 0x290-0x29f has been reserved

[ 0.248101] system 00:0b: driver attached

[ 0.248108] system 00:0c: iomem range 0xe0000000-0xefffffff has been reserved

[ 0.248111] system 00:0c: driver attached

[ 0.248119] system 00:0d: iomem range 0x0-0x9ffff could not be reserved

[ 0.248122] system 00:0d: iomem range 0xc0000-0xcffff has been reserved

[ 0.248125] system 00:0d: iomem range 0xe0000-0xfffff could not be reserved

[ 0.248128] system 00:0d: iomem range 0x100000-0x7fffffff could not be reserved

[ 0.248131] system 00:0d: iomem range 0xfec00000-0xffffffff could not be reserved

[ 0.248133] system 00:0d: driver attached

[ 0.248538] PCI: Bridge: 0000:00:08.0

[ 0.248540] IO window: disabled.

[ 0.248544] MEM window: disabled.

[ 0.248546] PREFETCH window: disabled.

[ 0.248550] PCI: Bridge: 0000:00:0b.0

[ 0.248551] IO window: disabled.

[ 0.248553] MEM window: 0xfbf00000-0xfdffffff

[ 0.248556] PREFETCH window: 0x00000000d0000000-0x00000000dfffffff

[ 0.248559] PCI: Bridge: 0000:00:0c.0

[ 0.248560] IO window: disabled.

[ 0.248562] MEM window: disabled.

[ 0.248564] PREFETCH window: disabled.

[ 0.248567] PCI: Bridge: 0000:00:0d.0

[ 0.248568] IO window: disabled.

[ 0.248570] MEM window: disabled.

[ 0.248572] PREFETCH window: disabled.

[ 0.248575] PCI: Bridge: 0000:00:0e.0

[ 0.248576] IO window: disabled.

[ 0.248578] MEM window: disabled.

[ 0.248580] PREFETCH window: disabled.

[ 0.248582] PCI: Bridge: 0000:00:0f.0

[ 0.248584] IO window: disabled.

[ 0.248586] MEM window: disabled.

[ 0.248588] PREFETCH window: disabled.

[ 0.248590] PCI: Bridge: 0000:00:10.0

[ 0.248592] IO window: disabled.

[ 0.248594] MEM window: disabled.

[ 0.248596] PREFETCH window: disabled.

[ 0.248598] PCI: Bridge: 0000:00:11.0

[ 0.248600] IO window: disabled.

[ 0.248602] MEM window: disabled.

[ 0.248604] PREFETCH window: disabled.

[ 0.248614] PCI: Setting latency timer of device 0000:00:08.0 to 64

[ 0.248624] PCI: Setting latency timer of device 0000:00:0b.0 to 64

[ 0.248631] PCI: Setting latency timer of device 0000:00:0c.0 to 64

[ 0.248637] PCI: Setting latency timer of device 0000:00:0d.0 to 64

[ 0.248644] PCI: Setting latency timer of device 0000:00:0e.0 to 64

[ 0.248650] PCI: Setting latency timer of device 0000:00:0f.0 to 64

[ 0.248656] PCI: Setting latency timer of device 0000:00:10.0 to 64

[ 0.248662] PCI: Setting latency timer of device 0000:00:11.0 to 64

[ 0.248691] NET: Registered protocol family 2

[ 0.284135] IP route cache hash table entries: 65536 (order: 7, 524288 bytes)

[ 0.285261] TCP established hash table entries: 262144 (order: 10, 4194304 bytes)

[ 0.290510] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)

[ 0.291775] TCP: Hash tables configured (established 262144 bind 65536)

[ 0.291779] TCP reno registered

[ 0.300145] NET: Registered protocol family 1

[ 0.300271] checking if image is initramfs… it is

[ 0.752027] Switched to high resolution mode on CPU 0

[ 0.752164] Freeing initrd memory: 6537k freed

[ 0.760718] audit: initializing netlink socket (disabled)

[ 0.760738] type=2000 audit(1255418227.760:1): initialized

[ 0.760958] Total HugeTLB memory allocated, 0

[ 0.761066] VFS: Disk quotas dquot_6.5.1

[ 0.761098] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)

[ 0.761145] msgmni has been set to 4029

[ 0.761253] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)

[ 0.761256] io scheduler noop registered

[ 0.761259] io scheduler anticipatory registered

[ 0.761261] io scheduler deadline registered

[ 0.761271] io scheduler cfq registered (default)

[ 0.761302] pci 0000:00:00.0: Enabling HT MSI Mapping

[ 0.809616] pci 0000:00:07.0: Enabling HT MSI Mapping

[ 0.809631] pci 0000:00:08.0: Enabling HT MSI Mapping

[ 0.809647] pci 0000:00:0a.0: Enabling HT MSI Mapping

[ 0.809661] pci 0000:00:0b.0: Enabling HT MSI Mapping

[ 0.809675] pci 0000:00:0c.0: Enabling HT MSI Mapping

[ 0.809690] pci 0000:00:0d.0: Enabling HT MSI Mapping

[ 0.809704] pci 0000:00:0e.0: Enabling HT MSI Mapping

[ 0.809719] pci 0000:00:0f.0: Enabling HT MSI Mapping

[ 0.809734] pci 0000:00:10.0: Enabling HT MSI Mapping

[ 0.809748] pci 0000:00:11.0: Enabling HT MSI Mapping

[ 0.809771] pci 0000:02:00.0: Boot video device

[ 0.809888] PCI: Setting latency timer of device 0000:00:0b.0 to 64

[ 0.809908] assign_interrupt_mode Found MSI capability

[ 0.809929] Allocate Port Service[0000:00:0b.0:pcie00]

[ 0.809970] Allocate Port Service[0000:00:0b.0:pcie03]

[ 0.810029] PCI: Setting latency timer of device 0000:00:0c.0 to 64

[ 0.810046] assign_interrupt_mode Found MSI capability

[ 0.810061] Allocate Port Service[0000:00:0c.0:pcie00]

[ 0.810094] Allocate Port Service[0000:00:0c.0:pcie03]

[ 0.810151] PCI: Setting latency timer of device 0000:00:0d.0 to 64

[ 0.810169] assign_interrupt_mode Found MSI capability

[ 0.810183] Allocate Port Service[0000:00:0d.0:pcie00]

[ 0.810217] Allocate Port Service[0000:00:0d.0:pcie03]

[ 0.810273] PCI: Setting latency timer of device 0000:00:0e.0 to 64

[ 0.810291] assign_interrupt_mode Found MSI capability

[ 0.810305] Allocate Port Service[0000:00:0e.0:pcie00]

[ 0.810340] Allocate Port Service[0000:00:0e.0:pcie03]

[ 0.810399] PCI: Setting latency timer of device 0000:00:0f.0 to 64

[ 0.810416] assign_interrupt_mode Found MSI capability

[ 0.810430] Allocate Port Service[0000:00:0f.0:pcie00]

[ 0.810465] Allocate Port Service[0000:00:0f.0:pcie03]

[ 0.810521] PCI: Setting latency timer of device 0000:00:10.0 to 64

[ 0.810538] assign_interrupt_mode Found MSI capability

[ 0.810552] Allocate Port Service[0000:00:10.0:pcie00]

[ 0.810586] Allocate Port Service[0000:00:10.0:pcie03]

[ 0.810642] PCI: Setting latency timer of device 0000:00:11.0 to 64

[ 0.810659] assign_interrupt_mode Found MSI capability

[ 0.810674] Allocate Port Service[0000:00:11.0:pcie00]

[ 0.810709] Allocate Port Service[0000:00:11.0:pcie03]

[ 0.812105] Linux agpgart interface v0.103

[ 0.812109] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled

[ 0.812258] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A

[ 0.812368] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A

[ 0.812530] pnp: the driver ‘serial’ has been registered

[ 0.812718] 00:0a: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A

[ 0.812758] serial 00:0a: driver attached

[ 0.814197] brd: module loaded

[ 0.814277] input: Macintosh mouse button emulation as /class/input/input0

[ 0.814378] pnp: the driver ‘i8042 kbd’ has been registered

[ 0.814394] i8042 kbd 00:09: driver attached

[ 0.814425] pnp: the driver ‘i8042 aux’ has been registered

[ 0.814462] PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1

[ 0.814464] PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp

[ 0.814907] serio: i8042 KBD port at 0x60,0x64 irq 1

[ 0.820332] mice: PS/2 mouse device common for all mice

[ 0.820371] pnp: the driver ‘rtc_cmos’ has been registered

[ 0.820450] rtc_cmos 00:07: rtc core: registered rtc_cmos as rtc0

[ 0.820475] rtc0: alarms up to one year, y3k

[ 0.820477] rtc_cmos 00:07: driver attached

[ 0.820505] cpuidle: using governor ladder

[ 0.820507] cpuidle: using governor menu

[ 0.820513] No iBFT detected.

[ 0.820928] TCP cubic registered

[ 0.820931] NET: Registered protocol family 17

[ 0.821053] registered taskstats version 1

[ 0.821257] rtc_cmos 00:07: setting system clock to 2009-10-13 07:17:08 UTC (1255418228)

[ 0.821267] Freeing unused kernel memory: 392k freed

[ 0.839374] input: AT Translated Set 2 keyboard as /class/input/input1

[ 0.913464] ACPI: ACPI0007:00 is registered as cooling_device0

[ 1.520658] ohci_hcd: 2006 August 04 USB 1.1 ‘Open’ Host Controller (OHCI) Driver

[ 1.521111] ACPI: PCI Interrupt Link [LUB0] enabled at IRQ 23

[ 1.521122] ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [LUB0] -> GSI 23 (level, low) -> IRQ 23

[ 1.521141] PCI: Setting latency timer of device 0000:00:02.0 to 64

[ 1.521144] ohci_hcd 0000:00:02.0: OHCI Host Controller

[ 1.521309] ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 1

[ 1.521333] ohci_hcd 0000:00:02.0: irq 23, io mem 0xfbe7f000

[ 1.578159] usb usb1: configuration #1 chosen from 1 choice

[ 1.578194] hub 1-0:1.0: USB hub found

[ 1.578208] hub 1-0:1.0: 6 ports detected

[ 1.578378] No dock devices found.

[ 1.595915] SCSI subsystem initialized

[ 1.610860] libata version 3.00 loaded.

[ 1.680210] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001

[ 1.680215] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1

[ 1.680218] usb usb1: Product: OHCI Host Controller

[ 1.680220] usb usb1: Manufacturer: Linux 2.6.26-2-amd64 ohci_hcd

[ 1.680222] usb usb1: SerialNumber: 0000:00:02.0

[ 1.680714] ACPI: PCI Interrupt Link [UB11] enabled at IRQ 22

[ 1.680726] ACPI: PCI Interrupt 0000:00:04.0[A] -> Link [UB11] -> GSI 22 (level, low) -> IRQ 22

[ 1.680746] PCI: Setting latency timer of device 0000:00:04.0 to 64

[ 1.680749] ohci_hcd 0000:00:04.0: OHCI Host Controller

[ 1.680810] ohci_hcd 0000:00:04.0: new USB bus registered, assigned bus number 2

[ 1.680836] ohci_hcd 0000:00:04.0: irq 22, io mem 0xfbe7d000

[ 1.738160] usb usb2: configuration #1 chosen from 1 choice

[ 1.738199] hub 2-0:1.0: USB hub found

[ 1.738212] hub 2-0:1.0: 6 ports detected

[ 1.840133] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001

[ 1.840137] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1

[ 1.840140] usb usb2: Product: OHCI Host Controller

[ 1.840142] usb usb2: Manufacturer: Linux 2.6.26-2-amd64 ohci_hcd

[ 1.840144] usb usb2: SerialNumber: 0000:00:04.0

[ 1.840638] ACPI: PCI Interrupt Link [LUB2] enabled at IRQ 21

[ 1.840650] ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [LUB2] -> GSI 21 (level, low) -> IRQ 21

[ 1.840668] PCI: Setting latency timer of device 0000:00:02.1 to 64

[ 1.840671] ehci_hcd 0000:00:02.1: EHCI Host Controller

[ 1.840730] ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 3

[ 1.840767] ehci_hcd 0000:00:02.1: debug port 1

[ 1.840771] PCI: cache line size of 64 is not supported by device 0000:00:02.1

[ 1.840787] ehci_hcd 0000:00:02.1: irq 21, io mem 0xfbe7ec00

[ 1.984008] usb 1-1: new full speed USB device using ohci_hcd and address 2

[ 1.996006] ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004

[ 1.996081] usb usb3: configuration #1 chosen from 1 choice

[ 1.996114] hub 3-0:1.0: USB hub found

[ 1.996124] hub 3-0:1.0: 6 ports detected

[ 2.052015] hub 1-0:1.0: unable to enumerate USB device on port 1

[ 2.100084] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002

[ 2.100087] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1

[ 2.100089] usb usb3: Product: EHCI Host Controller

[ 2.100091] usb usb3: Manufacturer: Linux 2.6.26-2-amd64 ehci_hcd

[ 2.100093] usb usb3: SerialNumber: 0000:00:02.1

[ 2.100509] ACPI: PCI Interrupt Link [UB12] enabled at IRQ 20

[ 2.100517] ACPI: PCI Interrupt 0000:00:04.1[B] -> Link [UB12] -> GSI 20 (level, low) -> IRQ 20

[ 2.100531] PCI: Setting latency timer of device 0000:00:04.1 to 64

[ 2.100534] ehci_hcd 0000:00:04.1: EHCI Host Controller

[ 2.100582] ehci_hcd 0000:00:04.1: new USB bus registered, assigned bus number 4

[ 2.100616] ehci_hcd 0000:00:04.1: debug port 1

[ 2.100619] PCI: cache line size of 64 is not supported by device 0000:00:04.1

[ 2.100632] ehci_hcd 0000:00:04.1: irq 20, io mem 0xfbe7e800

[ 2.112008] ehci_hcd 0000:00:04.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004

[ 2.112080] usb usb4: configuration #1 chosen from 1 choice

[ 2.112110] hub 4-0:1.0: USB hub found

[ 2.112120] hub 4-0:1.0: 6 ports detected

[ 2.216084] usb usb4: New USB device found, idVendor=1d6b, idProduct=0002

[ 2.216087] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1

[ 2.216089] usb usb4: Product: EHCI Host Controller

[ 2.216091] usb usb4: Manufacturer: Linux 2.6.26-2-amd64 ehci_hcd

[ 2.216093] usb usb4: SerialNumber: 0000:00:04.1

[ 2.216160] forcedeth: Reverse Engineered nForce ethernet driver. Version 0.61.

[ 2.216539] ACPI: PCI Interrupt Link [LMAC] enabled at IRQ 23

[ 2.216542] ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LMAC] -> GSI 23 (level, low) -> IRQ 23

[ 2.216547] PCI: Setting latency timer of device 0000:00:0a.0 to 64

[ 2.612007] usb 3-1: new high speed USB device using ehci_hcd and address 2

[ 2.736836] forcedeth 0000:00:0a.0: ifname eth0, PHY OUI 0x732 @ 1, addr 00:19:66:89:46:75

[ 2.736840] forcedeth 0000:00:0a.0: highdma pwrctl mgmt timirq gbit lnktim msi desc-v3

[ 2.743233] Uniform Multi-Platform E-IDE driver

[ 2.743239] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx

[ 2.744749] NFORCE-MCP67: 0000:00:06.0 (rev a1) UDMA133 controller

[ 2.744754] NFORCE-MCP67: IDE controller (0x10de:0x0560 rev 0xa1) at PCI slot 0000:00:06.0

[ 2.744783] NFORCE-MCP67: not 100% native mode: will probe irqs later

[ 2.744788] NFORCE-MCP67: BIOS didn’t set cable bits correctly. Enabling workaround.

[ 2.744794] NFORCE-MCP67: IDE port disabled

[ 2.744800] ide0: BM-DMA at 0xffa0-0xffa7

[ 2.744807] Probing IDE interface ide0…

[ 2.755508] usb 3-1: configuration #1 chosen from 1 choice

[ 2.755858] usb 3-1: New USB device found, idVendor=0ace, idProduct=1215

[ 2.755861] usb 3-1: New USB device strings: Mfr=16, Product=32, SerialNumber=0

[ 2.755863] usb 3-1: Product: USB2.0 WLAN

[ 2.755865] usb 3-1: Manufacturer: ZyDAS

[ 2.992016] usb 3-4: new high speed USB device using ehci_hcd and address 3

[ 3.135119] usb 3-4: configuration #1 chosen from 1 choice

[ 3.135316] usb 3-4: New USB device found, idVendor=1005, idProduct=b113

[ 3.135318] usb 3-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3

[ 3.135321] usb 3-4: Product: USB FLASH DRIVE

[ 3.135322] usb 3-4: Manufacturer:

[ 3.135324] usb 3-4: SerialNumber: 199617815025

[ 3.144136] hda: TSSTcorp CDDVDW SH-S202J, ATAPI CD/DVD-ROM drive

[ 3.157888] Initializing USB Mass Storage driver…

[ 3.316130] scsi0 : SCSI emulation for USB Mass Storage devices

[ 3.316475] usbcore: registered new interface driver usb-storage

[ 3.316479] USB Mass Storage support registered.

[ 3.318677] usb-storage: device found at 3

[ 3.318682] usb-storage: waiting for device to settle before scanning

[ 3.424102] hdb: Maxtor 4R080L0, ATA DISK drive

[ 3.480059] hda: host max PIO5 wanted PIO255(auto-tune) selected PIO4

[ 3.480232] hda: drive side 80-wire cable detection failed, limiting max speed to UDMA33

[ 3.480235] hda: UDMA/33 mode selected

[ 3.480456] hdb: host max PIO5 wanted PIO255(auto-tune) selected PIO4

[ 3.480596] hdb: UDMA/133 mode selected

[ 3.480754] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14

[ 3.480793] isa bounce pool size: 16 pages

[ 3.532201] hda: ATAPI 48X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache

[ 3.532209] Uniform CD-ROM driver Revision: 3.20

[ 3.534624] hdb: max request size: 128KiB

[ 3.535232] hdb: 160086528 sectors (81964 MB) w/2048KiB Cache, CHS=65535/16/63

[ 3.535377] hdb: cache flushes supported

[ 3.535425] hdb: hdb1 hdb2 hdb3 < hdb5 >

[ 3.620044] usb 2-1: new low speed USB device using ohci_hcd and address 2

[ 3.834116] usb 2-1: configuration #1 chosen from 1 choice

[ 3.837218] usb 2-1: New USB device found, idVendor=1241, idProduct=1111

[ 3.837222] usb 2-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0

[ 3.859466] usbcore: registered new interface driver hiddev

[ 3.870402] input: HID 1241:1111 as /class/input/input2

[ 3.876074] input,hidraw0: USB HID v1.10 Mouse [HID 1241:1111] on usb-0000:00:04.0-1

[ 3.876096] usbcore: registered new interface driver usbhid

[ 3.876099] usbhid: v2.6:USB HID core driver

[ 4.077583] PM: Starting manual resume from disk

[ 4.150277] kjournald starting. Commit interval 5 seconds

[ 4.150277] EXT3-fs: mounted filesystem with ordered data mode.

[ 6.403662] udevd version 125 started

[ 7.738600] input: Power Button (FF) as /class/input/input3

[ 7.764091] ACPI: Power Button (FF) [PWRF]

[ 7.764206] input: Power Button (CM) as /class/input/input4

[ 7.792103] ACPI: Power Button (CM) [PWRB]

[ 8.316231] usb-storage: device scan complete

[ 8.318086] scsi 0:0:0:0: Direct-Access USB FLASH DRIVE PMAP PQ: 0 ANSI: 0 CCS

[ 8.390969] ACPI: WMI: Mapper loaded

[ 8.664036] usb 3-1: reset high speed USB device using ehci_hcd and address 2

[ 8.797803] phy0: Selected rate control algorithm ‘pid’

[ 8.879464] ACPI: PCI Interrupt Link [LAZA] enabled at IRQ 22

[ 8.879470] ACPI: PCI Interrupt 0000:00:07.0[A] -> Link [LAZA] -> GSI 22 (level, low) -> IRQ 22

[ 8.879497] PCI: Setting latency timer of device 0000:00:07.0 to 64

[ 8.912164] hda_codec: Unknown model for ALC662, trying auto-probe from BIOS…

[ 9.108178] input: PC Speaker as /class/input/input5

[ 9.209074] zd1211rw 3-1:1.0: phy0

[ 9.209099] usbcore: registered new interface driver zd1211rw

[ 9.224814] NET: Registered protocol family 23

[ 9.246548] pnp: the driver ‘parport_pc’ has been registered

[ 9.246570] parport_pc 00:05: reported by Plug and Play ACPI

[ 9.246624] parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE]

[ 9.340174] parport_pc 00:05: driver attached

[ 9.377617] Driver ‘sd’ needs updating - please use bus_type methods

[ 10.749056] sd 0:0:0:0: [sda] 7831552 512-byte hardware sectors (4010 MB)

[ 10.751920] sd 0:0:0:0: [sda] Write Protect is off

[ 10.751923] sd 0:0:0:0: [sda] Mode Sense: 23 00 00 00

[ 10.751926] sd 0:0:0:0: [sda] Assuming drive cache: write through

[ 10.762046] sd 0:0:0:0: [sda] 7831552 512-byte hardware sectors (4010 MB)

[ 10.764923] sd 0:0:0:0: [sda] Write Protect is off

[ 10.764926] sd 0:0:0:0: [sda] Mode Sense: 23 00 00 00

[ 10.764928] sd 0:0:0:0: [sda] Assuming drive cache: write through

[ 10.764965] sda: sda1

[ 10.767151] sd 0:0:0:0: [sda] Attached SCSI removable disk

[ 12.052001] Adding 1839400k swap on /dev/hdb5. Priority:-1 extents:1 across:1839400k

[ 12.666905] EXT3 FS on hdb2, internal journal

[ 13.113452] loop: module loaded

[ 15.140336] eth0: no link during initialization.

[ 16.785866] powernow-k8: Found 1 AMD Athlon™ 64 Processor 3200+ processors (1 cpu cores) (version 2.20.00)

[ 16.785915] powernow-k8: 0 : fid 0xe (2200 MHz), vid 0x2

[ 16.785917] powernow-k8: 1 : fid 0xc (2000 MHz), vid 0x6

[ 16.785919] powernow-k8: 2 : fid 0xa (1800 MHz), vid 0xa

[ 16.785922] powernow-k8: 3 : fid 0x2 (1000 MHz), vid 0x12

[ 18.091946] NET: Registered protocol family 10

[ 18.092513] lo: Disabled Privacy Extensions

[ 18.093188] ADDRCONF(NETDEV_UP): eth0: link is not ready

[ 18.272109] Marking TSC unstable due to cpufreq changes

[ 18.748016] Clocksource tsc unstable (delta = -262239479 ns)

[ 28.580526] lp0: using parport0 (interrupt-driven).

[ 28.625717] ppdev: user-space parallel port driver

[ 34.949750] firmware: requesting zd1211/zd1211b_ub

[ 35.020098] usb 3-1: Could not load firmware file zd1211/zd1211b_ub. Error number -2

[ 35.020127] zd1211rw 3-1:1.0: couldn’t load firmware. Error number -2

[ 37.720541] firmware: requesting zd1211/zd1211b_ub

[ 37.733177] usb 3-1: Could not load firmware file zd1211/zd1211b_ub. Error number -2

[ 37.733186] zd1211rw 3-1:1.0: couldn’t load firmware. Error number -2

[ 42.137293] nvidia: module license ‘NVIDIA’ taints kernel.

[ 42.404626] ACPI: PCI Interrupt Link [LNEB] enabled at IRQ 19

[ 42.404635] ACPI: PCI Interrupt 0000:02:00.0[A] -> Link [LNEB] -> GSI 19 (level, low) -> IRQ 19

[ 42.404643] PCI: Setting latency timer of device 0000:02:00.0 to 64

[ 42.404812] NVRM: loading NVIDIA UNIX x86_64 Kernel Module 173.14.09 Wed Jun 4 23:40:50 PDT 2008

[ 54.788144] firmware: requesting zd1211/zd1211b_ub

[ 54.800614] usb 3-1: Could not load firmware file zd1211/zd1211b_ub. Error number -2

[ 54.800622] zd1211rw 3-1:1.0: couldn’t load firmware. Error number -2

[ 68.051210] FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!

[ 71.828233] firmware: requesting zd1211/zd1211b_ub

[ 71.836223] usb 3-1: Could not load firmware file zd1211/zd1211b_ub. Error number -2

[ 71.836235] zd1211rw 3-1:1.0: couldn’t load firmware. Error number -2

[ 88.892140] firmware: requesting zd1211/zd1211b_ub

[ 88.904659] usb 3-1: Could not load firmware file zd1211/zd1211b_ub. Error number -2

[ 88.904668] zd1211rw 3-1:1.0: couldn’t load firmware. Error number -2

[ 105.972152] firmware: requesting zd1211/zd1211b_ub

[ 105.984679] usb 3-1: Could not load firmware file zd1211/zd1211b_ub. Error number -2

[ 105.984688] zd1211rw 3-1:1.0: couldn’t load firmware. Error number -2

[ 123.008144] firmware: requesting zd1211/zd1211b_ub

[ 123.020813] usb 3-1: Could not load firmware file zd1211/zd1211b_ub. Error number -2

[ 123.020821] zd1211rw 3-1:1.0: couldn’t load firmware. Error number -2

[ 140.064165] firmware: requesting zd1211/zd1211b_ub

[ 140.076882] usb 3-1: Could not load firmware file zd1211/zd1211b_ub. Error number -2

[ 140.076890] zd1211rw 3-1:1.0: couldn’t load firmware. Error number -2

[ 157.104187] firmware: requesting zd1211/zd1211b_ub

[ 157.116952] usb 3-1: Could not load firmware file zd1211/zd1211b_ub. Error number -2

[ 157.116960] zd1211rw 3-1:1.0: couldn’t load firmware. Error number -2

[ 279.144146] firmware: requesting zd1211/zd1211b_ub

[ 279.156704] usb 3-1: Could not load firmware file zd1211/zd1211b_ub. Error number -2

[ 279.156709] zd1211rw 3-1:1.0: couldn’t load firmware. Error number -2
[/code]

#4

Ah, apparemment le module a besoin d’un firmware qui se trouve dans le paquet zd1211-firmware présent dans le dépôt non-free. Installe ce paquet et recharge le module zd1211rw (modprobe -r zd1211rw && modprobe zd1211rw) ou redémarre le système. Si cela suffit, tu n’auras pas besoin de recompiler.

#5

Merci pour tes repenses rapid :smiley:

je vien d installer zd1211-firmware

mais je ne sais pas comment recharge le module zd1211rw (modprobe -r zd1211rw && modprobe zd1211rw)

je suis debutant :confused:

#6

Tu exécutes la commande indiquée dans une console root comme tu l’as fait pour dmesg et ifconfig. Ou bien tu redémarres comme une brute si ta fierté ou toute autre contrainte ne te l’interdit pas.

#7

re voilà c fais :wink:
quand je lance wifi-radar il detecte rien

#8

Rechargé le module ou redémarré le système ?
Pour wifi-radar faut pas me demander, je n’y connais rien en wifi. Pour le reste, tu peux vérifier avec dmesg s’il n’y a plus de message d’erreur lié à l’adaptateur. (Pas la peine de tout recopier ici, juste ce qui concerne l’adaptateur le cas échéant)

#9

j ai recharger le module

[ 953.929734] firmware: requesting zd1211/zd1211b_ub [ 953.985692] firmware: requesting zd1211/zd1211b_uphr [ 954.049631] zd1211rw 3-1:1.0: RF MAXIM_NEW_RF 0x8 is not supported [ 956.696212] firmware: requesting zd1211/zd1211b_ub [ 956.705626] firmware: requesting zd1211/zd1211b_uphr [ 983.764147] firmware: requesting zd1211/zd1211b_ub [ 983.777675] firmware: requesting zd1211/zd1211b_uphr [ 984.796040] usb 3-1: USB control request for firmware upload failed. Error number -110 [ 984.796047] usb 3-1: Could not upload firmware code uph. Error number -110 [ 984.796056] zd1211rw 3-1:1.0: couldn't load firmware. Error number -110 [ 1006.868152] firmware: requesting zd1211/zd1211b_ub [ 1006.881611] firmware: requesting zd1211/zd1211b_uphr [ 1007.896203] usb 3-1: USB control request for firmware upload failed. Error number -110 [ 1007.896213] usb 3-1: Could not upload firmware code uph. Error number -110 [ 1007.896227] zd1211rw 3-1:1.0: couldn't load firmware. Error number -110 [ 1029.968188] firmware: requesting zd1211/zd1211b_ub [ 1029.984488] firmware: requesting zd1211/zd1211b_uphr [ 1031.000049] usb 3-1: USB control request for firmware upload failed. Error number -110

#10

Comme je le craignais, il y a le message concernant la puce RF non supportée. Il faut donc patcher et recompiler le module. Concernant l’autre message d’erreur de chargement du firmware, je n’ai pas d’explication.

#11

merci comme meme pour ton aide PascalHambourg :wink:
dsl pour le derangement

#12

J’y pense, si tu ne souhaites pas recompiler (ce n’est pas si difficile), tu peux installer un noyau 2.6.29 ou 2.6.30 de lenny-backports.

#13

Je ne sais pas comment faire ?

#14

installer un noyau 2.6.30 de lenny-backports.

#15

Il doit y avoir un fil dans le forum “trucs & astuces” pour ajouter le dépôt lenny-backports et gérer les priorités pour ne pas que les paquets de lenny-backports aient priorité sur ceux de lenny. Il y a plus simple pour tester : télécharger le .deb et l’installer à la main avec la commande dpkg -i <nomfichier.deb>.
Page de linux-image-2.6.29-bpo.2-amd64
Page de linux-image-2.6.30-bpo.2-amd64
Par contre je ne connais pas le statut de ces paquets vis-à-vis du suivi de sécurité.

#16

voilà je vien d installer linux-image-2.6.30-bpo.2-amd64_2.6.30-7~bpo50+1_amd64.deb

Sélection du paquet linux-image-2.6.30-bpo.2-amd64 précédemment désélectionné. (Lecture de la base de données... 112884 fichiers et répertoires déjà installés.) Dépaquetage de linux-image-2.6.30-bpo.2-amd64 (à partir de linux-image-2.6.30-bpo.2-amd64_2.6.30-7~bpo50+1_amd64.deb) ... Paramétrage de linux-image-2.6.30-bpo.2-amd64 (2.6.30-7~bpo50+1) ... Running depmod. Running update-initramfs. update-initramfs: Generating /boot/initrd.img-2.6.30-bpo.2-amd64 Running update-grub. Searching for GRUB installation directory ... found: /boot/grub Searching for default file ... found: /boot/grub/default Testing for an existing GRUB menu.lst file ... found: /boot/grub/menu.lst Searching for splash image ... none found, skipping ... Found kernel: /boot/vmlinuz-2.6.30-bpo.2-amd64 Found kernel: /boot/vmlinuz-2.6.26-2-amd64 Updating /boot/grub/menu.lst ... done

#17

Maintenant il faut redémarrer, sélectionner ce noyau dans le menu de grub et voir ce que ça donne. A noter qu’il n’est pas exclu que ce noyau provoque d’autres problèmes, notamment avec les pilotes graphiques.

#18

je me suis connecter sur kernel 2.6.30-bpo.2-amd64
direct erreur x server j ai flippé mdr

le xorg.conf qui fonctione sur kernel 2.6.26-2 amd64

[code]Section "InputDevice"
Identifier "Generic Keyboard"
Driver "kbd"
Option “XkbRules” "xorg"
Option “XkbModel” "pc105"
Option “XkbLayout” "be"
EndSection

Section "InputDevice"
Identifier "Configured Mouse"
Driver "mouse"
EndSection

Section "Device"
Identifier "Configured Video Device"
Driver "nvidia"
Option “NoLogo” "True"
EndSection

Section "Monitor"
Identifier "Configured Monitor"
EndSection

Section "Screen"
Identifier "Default Screen"
Monitor "Configured Monitor"
EndSection
[/code]

#19

C’est ce que je craignais. Le pilote nvidia dépend de la version du noyau et doit être recompilé ou réinstallé pour tenir compte du nouveau noyau, je ne sais pas exactement car je ne l’utilise pas.

Tu peux quand même vérifier en ligne de commande si les erreurs du module wifi ont disparu.

Ensuite, tu as deux possibilités : soit tu réinstalles le pilote nvidia pour qu’il fonctionne avec le noyau 2.6.30 (et en espérant qu’il n’y a rien d’autre d’incompatible), soit tu compiles un noyau 2.6.26 patché. Je pourrai te fournir une procédure quand je l’aurai validée.

#20

j ai tester avec dmesg
j ai pas vu ce genre d erreur

pour l instalation du nvidia sur le nouveau noyau

il m a ecrit
les en tetes du noyau pour la version cible n ont pas etais trouvés et vous avez pas indiqué d autres en tetes valable a utilisé